Which juicer format should a wholesale buyer shortlist?
Shortlist a slow-auger juicer when the brief specifically calls for an auger-pressing format; shortlist a centrifugal juice extractor when the brief calls for that format. If the brief instead depends on measured juice recovery, preparation effort or handling, keep both candidates open until comparable samples answer those questions. LH-805/P430 and LH-618/P438 provide different published configurations, not a proven performance ranking. Neither wattage, feed opening nor container size establishes which sample will meet your intended use.
Define the product format before comparing numbers
This comparison concerns a slow-auger pressing juicer and a centrifugal juice extractor. It does not compare a citrus press or a blender attachment set. A buyer asking for a "juicer" should first identify which format belongs in the product brief, then confirm the permitted ingredients and preparation instructions for the exact sample.
If the project requires a combination appliance, use the juicer-blender model and order-control guide. For the wider range, start with slow juicer records and juice extractor and citrus juicer records; the latter group contains distinct formats, not interchangeable products.
Compare two catalog configurations without predicting performance
The fields below come from the published LH-805 and LH-618 catalog records. They are two model examples, not specifications for every slow or centrifugal juicer. Final construction, included parts and electrical version remain subject to the current sample and written order specification.
| Decision field | LH-805 / P430 | LH-618 / P438 | What the buyer must not assume |
|---|---|---|---|
| Extraction format | Slow-auger pressing | Centrifugal juice extractor; stainless-steel juicing filter; separate juice and pulp outlets | Format alone does not establish measured juice recovery, nutrient retention or an approved ingredient list. |
| Power and motor | 200 W; DC motor | 350 W; catalog motor options 7020 / 7025 | Wattage is not a measured throughput or yield result. Select the LH-618 motor option in writing. |
| Feed dimension | 110 mm feed opening diameter | 65 mm feed tube internal diameter | The opening is not permission to feed every ingredient whole. Confirm preparation and feeding instructions. |
| Collection containers | 700 mL juice cup; 500 mL pulp container | 550 mL juice cup; 1000 mL pulp container | These are container capacities, not juice yield, usable batch size or a continuous-duty allowance. |
| Controls to confirm | Reverse function listed; confirm reverse control and spout configuration | Pulse / Off / 1 / 2 positions | A listed control does not establish run time, permitted load or jam-clearing instructions. |
Both records list electrical version choices of 110–120 V or 220–240 V, with 50/60 Hz references. Select the order version for the destination; these alternatives do not establish automatic dual-voltage operation.
Open the exact LH-805 slow juicer record or LH-618 centrifugal extractor record. Their current images are disclosed as AI-generated catalog illustrations, not product photographs. Do not approve construction, appearance, accessories or performance from those illustrations.
If juice recovery drives the choice, agree one comparison basis
A claim such as "more juice" is not a usable comparison unless the input and collection rules are known. The following is a proposed buyer worksheet, not completed Yaoyuan testing, a certification protocol or a universal acceptance threshold. Use only ingredients and procedures permitted by each sample's instructions. If the samples require different preparation or operation, record that difference rather than forcing an unsafe identical procedure.
- Match the input basis. Record ingredient type, lot or source, starting condition and preparation. Weigh and record the prepared mass actually fed in each run, after any agreed peeling, trimming or seed removal; record unused prepared material separately. Do not compare whole purchased fruit weight on one sample with prepared input weight on the other.
- Define what counts as collected juice. Agree whether foam or suspended pulp is included, whether straining is used, the collection endpoint and the weighing equipment. Use a consistent, instruction-permitted starting condition and the same stated collection endpoint or elapsed collection interval for the compared runs; record any carry-over from a previous run. Tare the empty receiving container and record collected juice mass in the same unit as the prepared input. Keep added water or other liquid outside this simple comparison; if required, define a different accounting method first.
- Keep the operating record beside the result. Identify each model, sample revision, filter, electrical version, control sequence, permitted run/rest intervals, repeat runs and any interruption. Missing measurements stay unknown, not zero. An incomplete run stays visibly incomplete; do not calculate a comparable recovery percentage for it or combine it with completed runs.
For this buyer-defined mass basis only: collected juice mass ÷ prepared mass actually fed × 100 gives a recorded recovery percentage for that run. Calculate it only when the input mass is positive and both measurements are available; missing or incomplete results remain unreported, not zero. Do not substitute cup capacity or a volume in mL for a mass in g. The number does not establish nutrient retention, noise, taste, cleaning effort or results with other ingredients. Retain each run and its conditions, not only the best result.
Assess preparation and cleaning separately using the exact instructions. A larger opening does not prove less preparation, and a removable part does not establish a dishwasher-safe or immersion-safe cleaning method.
End the comparison with a shortlist decision, not an unsupported winner
- Advance the slow-auger candidate. Record that auger pressing is a required product-format choice, or reference the buyer-reviewed sample record that supports this candidate for the stated use. List any outstanding LH-805 control, spout or ingredient questions.
- Advance the centrifugal candidate. Record that a centrifugal extractor is the required format, or reference the buyer-reviewed sample record supporting that choice. Retain the exact LH-618 motor option, filter, controls and collection set in the brief.
- Keep both candidates open. Use this outcome when the format is not fixed and comparable evidence is missing or inconclusive. Name the unresolved buyer question, the needed sample record and the person responsible for the next review. Do not fill the gap with a category-wide "better yield" or "healthier juice" claim.
Advancing a candidate authorizes the next sourcing discussion, not production or shipment release. Once the exact sample is accepted, continue with golden sample approval and retention and the technical and quality annex rather than recreating the order record here. Certification documents depend on the exact model and target market.
Buyer questions
Does a slow juicer necessarily produce more juice?
Not on the evidence published here. A category name is not a measured result. Compare the selected samples using a stated ingredient, preparation, input mass and collection method; keep any conclusion limited to the recorded conditions.
Can a 110 mm opening be advertised as whole-fruit capability?
The opening dimension alone does not establish that claim. Confirm the permitted ingredients, preparation, feeding method and instructions for the exact sample before approving such wording.
Do I need a finished test specification before asking for a quotation?
No. Start with the intended market, preferred format or unresolved use question, planned quantity and business contact. Identify unknown details for follow-up. A sourcing discussion does not mean a performance claim or order specification has been approved.
Discuss a slow or centrifugal juicer wholesale project
Share the preferred format, intended ingredients or use case, target market and open comparison questions. For a private quotation, confirm product model, quantity, country, plug type, voltage, packing request, OEM request and destination port. This guide adds no mandatory RFQ fields.
Factory direct. Wholesale only. MOQ starts from 1000 PCS. Retail and one-piece orders are not accepted. Prices remain private.